IC697CMM742

GE Fanuc | 9070 | GE Fanuc 90-70 PLC

IC697CMM742 Image

IC697CMM742

Same Day - Free Shipping

  • Manufacturer: GE Fanuc
  • Description: GE Fanuc Series 90-70 Ethernet Interface Unit Tupe 2
  • Weight: 4 lbs :: ≈ 2 kgs
  • Warranty: 1 Years
  • Product Revisions Available:
  • Other Available Revisions of the IC697CMM742 : -CC, -DC, -DD, -ED, -FD, -FE, -FF, -FG, -GH, -HJ, -HK, -JL, -LL, -ML,

Product Manual Excerpt

Connects IC697 PLC to an IEEE 802.3 CSMA/CD 10Mbps Ethernet LAN via one of three network ports: 10BaseT, 10Base2, or AUI 10BaseT and 10Base2 network ports provide direct connection to 10BaseT or 10Base2 network without an external transceiver Standard 15-pin AUI network port allows choice of 10Base5, 10Base2, 10BaseT, 10BaseF, or 10Broad36 medium with user-supplied 802.3-compatible transceiver Firmware is pre-loaded for easy installation and is maintained indefinitely; firmware is easily upgraded in-system from PC attached to RS-485 serial port The Ethernet Interface provides: Data exchange using configuration-based and logic-based Ethernet Global Data TCP/IP communication services using SRTP Full PLC programming and configuration services Comprehensive station management and diagnostic tools Functions The IC697CMM742 Ethernet Interface (Type 2) provides high performance TCP/IP communications for the IC697 PLC. The Ethernet Interface (Type 2) plugs into a single slot in an IC697 PLC rack and is configured with the IC641 PLC programming software. Up to four Ethernet Interface (Type 2) modules can be installed in an IC697 PLC CPU rack. The Ethernet Interface (Type 2) contains three network ports: 10BaseT (RJ-45 connector), 10Base2 (BNC connector), and AUI (15-pin D-connector). The Ethernet Interface automatically selects the network port in use. One network port may be used at a time. The 10BaseT network port permits direct connection to a 10BaseT (twisted pair) network hub or repeater without an external transceiver. The 10Base2 network port permits direct connection to a 10Base2 (ThinWire ) network without an external transceiver. The AUI network port permits attachment of a usersupplied AUI (Attachment Unit Interface, or transceiver) cable. ETHERNET INTERFACE MODULE OK LAN ONLINE SERIAL ACTIVE STATUS RESTART STATION MGR RS 232 SERVICE OPTION S/W LOAD RS 485 C O N N E C E R N E T N a45632 The AUI cable connects the Ethernet Interface to a user-supplied transceiver that is directly connected to the 10Mbps Ethernet network. The transceiver must be 802.3 compatible and must have the SQE option enabled. ThinWire is a trademark of Digital Equipment Corporation. MS-DOS, Windows, Windows 95, and Windows NT are registered trademarks of Microsoft Corporation. GFK-1309E Ethernet Interface (Type 2) 2 Communications Modules September 1998 Series 90 -70 Programmable Controller Data Sheet Manual GFK-0600F 69-2 Transceivers are commercially available to operate on a variety of 10Mbps media including 0.4 inch diameter coaxial cable (10Base5), ThinWire coaxial cable (10Base2), twisted pair (10BaseT), fiber optic (10BaseF), and broadband cable (10Broad36). The Ethernet Interface (Type 2) provides TCP/IP communications with other IC697 and IC693 PLCs, host computers running the Host Communications Toolkit or CIMPLICITY software, and computers running the TCP/IP version of the MS-DOS or Windows based programming software. These communications use the proprietary SRTP and Ethernet Global Data protocols over a 4-layer TCP/IP (Internet) stack. Figure 1 shows the IC697 PLC in a basic Ethernet communication system. IC697 PLC IC697 PLC a45633 Network Connection Ethernet Interface Tr ansce iver Ethernet Cable Host Computer or Control Device running a Host Communications Toolkit Application Tra nscei ver Ethernet IC641 Programming Software - TCP/IP Ethernet running on a PC Transceiver Ethernet Interface Figure 1. Ethernet Interface Connects the IC697 PLC to an 802.3 LAN IEEE 802.3 Media The Ethernet Interface (Type 2) can operate directly on 10BaseT or 10Base2 media via its 10baseT and 10Base2 network ports. These media are described below. Additionally, the Ethernet Interface (Type 2) can operate on any of the media listed below with the appropriate user-supplied transceiver and transceiver cable via its AUI network port. 10Base5 Coax: 10Base5 uses a 0.4 inch diameter 50-ohm coaxial cable. The maximum length of a cable segment (single span of cable) is 500 meters. The distance between any two stations must be a multiple of 2.5 meters. A maximum of 100 stations is allowed on a thickwire Ethernet segment. 10Base2 Coax: 10Base2 uses a 0.2 inch diameter 50-ohm coaxial cable. The maximum length of a ThinWire cable segment is 185 meters. A maximum of 30 stations is allowed on a ThinWire Ethernet segment. 10BaseT: 10BaseT uses a twisted pair cable of up to 100 meters in length between each node and a hub or repeater. Typical hubs or repeaters support 6 to 12 nodes connected in a star wiring topology. 10BaseF: 10BaseF has two variations that both use the same type of fiber optic cable: 10BaseFP can support up to 33 nodes at distances of up to 500 meters from a passive star; 10BaseFL supports up to 2000 meters between a node and a repeater (a multi-port repeater would thus constitute a star). Additionally, 10BaseFB provides a means of interconnecting (only) repeaters by up to 2000 meters of (the same) fiber optic cable. Note Various Ethernet baseband media listed above can be interconnected by appropriate repeaters. Capabilities and limitations are defined in IEEE 802.3 Chapter 13, System Considerations for Multi-Segment Networks. 10Broad36: 10Broad36 uses 75-ohm coaxial cable and CATV-like media components (taps, amplifiers, headend translators, etc.) to support hundreds of nodes at distances of up to 2800 meters. Broadband cannot be connected to baseband via repeaters. Broadband cable plant design and installation must be in accordance with IEEE 802.7 and requires special expertise. GE Fanuc recommends you contract professional specialists for these services. Consult your local authorized GE Fanuc PLC distributor, or your GE Fanuc sales representative or field service office for help in identifying local specialists. 3 Ethernet Interface (Type 2) GFK-1309E Communications Modules September 1998 Series 90 -70 Programmable Controller Data Sheet Manual GFK-0600F 69-3 Physical Description Figure 2 shows the maintenance items and indicators of the Ethernet Interface (Type 2). ETHERNET INTERFACE MODULE OK LAN ONLINE SERIAL ACTIVE STATUS RESTART STATION MGR RS 232 SERVICE OPTION S/W LOAD RS 485 C O NN E C TI ON 10 BASE T 10 BASE 2 OR AUI OR ET HE R NE T S E R IAL S C O NN E C TI ON DEFAULT STATION ADDRESS LABEL a45634 FU3 JP7 LEDS RESTART PUSHBUTTON STATION MGR (RS 232) SERIAL PORT SERVICE OPTION CONNECTOR SOFTWARE LOAD (RS 485) SERIAL PORT 10BaseT NETWORK PORT AUI NETWORK PORT 10Base2 NETWORK PORT 1 2 3 4 5 6 7 8 11 10 9 REPLACEABLE FUSE DISABLE ONBOARD 10Base2 PORT JUMPER Figure 2. Ethernet Controller Board User Maintenance Items The Ethernet Interface has the following useraccessible elements: 1. Four LEDs 2. Restart Pushbutton 3. Station Mgr (RS-232) Serial Port 4. Service Option Connector 5. Software Load (RS-485) Serial Port 6. 10BaseT Network Port 7. AUI Network Port 8. 10Base2 network Port 9. Default Station (MAC) Address Label (located on the inside edge of the module faceplate) 10. Replaceable +12 VDC Fuse (FU3) 11. Onboard 10base2 Transceiver Power Disable Jumper (JP7 - normally not installed) GFK-1309E Ethernet Interface (Type 2) 4 Communications Modules September 1998 Series

Need To Order A Specific Revision?

Give us a call at 1-800-360-6802 or 1-919-535-3180. We can help you with your Revision specific needs.


UPS Ground shipping is always FREE!


What is New Surplus?

These “New Surplus” units are a great cost saving alternative. This product is in the original manufacturer’s packaging with all sub-assemblies and documentation. Comes with a PLC Distribution Factory & Supply 3-year warranty.


UPS Ground shipping is always FREE!


What is Surplus New?

Surplus New - New unused and includes all sub-assemblies and documentation. Product may ship in manufacturer or PLC Distribution Factory & Supply packaging and includes a PLC Distribution Factory & Supply 3 Year Warranty.


UPS Ground shipping is always FREE!


What is Reconditioned?

Reconditioned products from PLC Distribution Factory & Supply are a cost-effective alternative to new and obsoleted PLC products. Every part is reconditioned down to the circuit board level. All parts are thoroughly inspected and hand-cleaned before being functionally tested in a fully configured system.


Our Reconditioned Products always come with a PLC Distribution Factory & Supply 2-Year Warranty.

UPS Ground shipping is always FREE!


110% PRICE MATCH GUARANTEE


We stand behind our prices with a 110% price match guarantee. If you buy a part from us and, within seven days of purchase, find that part advertised on an authorized distributor's website for less, simply contact us and give us a link to the lower advertised price and we'll refund you 110% of the difference between your purchase price and the advertised lower price. The part must be in-stock for immediate shipment and be in similar condition. All pricing must be displayed without signing in.

Repair Service


3-5 Days for most repairs. 24 hour repair upon request at no extra charge. If part is unrepairable, we will exchange with a working unit or return unrepaired.