IC697CMM741

GE Fanuc | 9070 | GE Fanuc 90-70 PLC

IC697CMM741 Image

IC697CMM741

Same Day - Free Shipping

  • Manufacturer: GE Fanuc
  • Description: Series 90-70 MMS or TCP/IP Ethernet Lan Interface
  • Weight: 4 lbs :: ≈ 2 kgs
  • Warranty: 1 Years
  • Product Revisions Available:
  • Other Available Revisions of the IC697CMM741 : A, B, C, D, E, F, G, H, I, J, K, L, M, N, O, P, Q, R, S, T, U, V, W, X, Y, Z, -KX, -LX,

Product Manual Excerpt

Direct PLC attachment to IEEE 802.3 CSMA/CD LAN Standard 15-pin AUI port connection allows choice of 10Base5, 10Base2, 10BaseT, 10BaseF, or 10Broad36 medium with user-supplied 802.3-compatible transceiver For IC697 programmable controllers Occupies a single slot in PLC rack Software (separately licensed) is easily loaded or upgraded via RAM load Software is retained through power outages for a minimum of six months Alternative software packages provide: - TCP/IP communications - MMS/OSI communications - Full MS-DOS or WIndows programming and configuration services - Comprehensive station management and diagnostic tools MS-DOS or WINDOWS PROGRAMMING SOFTWARE SYSTEM MANAGER LOCAL GSM ETHERNET CONTROLLER IC697 PLC TRANSCEIVER TRANSCEIVER TRANSCEIVER ETHERNET CONTROLLER IC697 PLC CABLE PLANT a44662 * * TRANSCEIVER CABLE SYSTEM MANAGER NETWORK GSM TRANSCEIVER Figure 1. Ethernet Controller Connects the IC697 PLC to a 802.3 LAN The Ethernet Controller is a member of the family of IC651 Factory LAN hardware and software products. The Factory LAN family of products provides high performance solutions for interconnecting automation controllers and for integrating them into multi-vendor networks. The Ethernet Controller plugs into a single slot in an IC697 PLC rack and provides an 802.3-standard 15-pin D-connector for attachment of a user-supplied AUI (Attachment Unit Interface) or transceiver cable. The AUI cable connects to a user-supplied transceiver that is directly connected to the 10Mbps Ethernet network cable. The transceiver must be 802.3-compatible and must have the SQE option enabled. Transceivers are commercially available to operate on a variety of 10Mbps media including thickwire coaxial cable (10Base5), ThinWire coaxial cable (10Base2), twisted pair (10BaseT), fiber optic (10BaseF), and broadband cable (10Broad36). The Ethernet Controller is designed so the communications protocols which operate above the Ethernet data link layer are implemented in software. This permits the user to choose between two* alternative communication protocols by downloading the Ethernet Controller with the applicable Communications Software: TCP/IP-Ethernet Communications Software - Communicate with host computers and/or MS-DOS or WIndows Programmer using proprietary SRTP over a 4-layer TCP/IP (Internet) protocol stack; requires either a Local or Network Factory LAN System Manager (GSM) for configuration and downloading of Ethernet Controller software. MMS-Ethernet Communications Software - Communicate with host computers and/or MS-DOS or Windows Programmer using MMS (Manufacturing Message Specification - ISO 9506) on a 7-layer OSI protocol stack; requires GSM for configuration and downloading of Ethernet Controller software. Figure 1 shows the general relationship between the Ethernet Controller, the local and network GSMs, and the MS-DOS or Windows Programming Software on Ethernet station. * A third option, SRTP communications software (IC641SWP711) supports only communications with MS-DOS or WIndows Programmers using SRTP over a 4-layer OSI protocol stack; this Ethernet Controller software does not require configuration and can be downloaded directly from the MS-DOS or Windows Programer. ThinWire is a trademark of Digital Equipment Corporation; IBM is a registered trademark of International Business Machines Corporation. MS-DOS, Windows, Windows 95 , and Windows NT are registered trademarks of Microsoft Corporation. GFK-0532K Ethernet Controller 2 Communications Modules August 1997 Series 90 -70 Programmable Controller Data Sheet Manual GFK-0600F 68-2 Features of the Ethernet Controller The Ethernet Controller is a single-slot module that is inserted directly into the IC697 CPU rack. Connection to the Ethernet LAN is made via a transceiver cable to an external transceiver. The transceiver and cable are provided by the user. The transceiver is attached directly to the IEEE 802.3 network cable. The Ethernet Interface operates at 10 Mbps on the Ethernet LAN. The Ethernet Controller uses three LEDs for indicating the status of the interface. A battery is provided to maintain the contents of Random Access Memory (RAM) over power outages. The Ethernet Controller provides basic functions in firmware or Read Only Memory (ROM). This firmware includes self-test diagnostics and special software that allows you to configure and test your interface in the PLC and on the Ethernet LAN. It also allows you to load the communications software into RAM either from the GSM (serially or over the network), or from an MS-DOS or Windows OSI-Ethernet Programmer station. The communications software is stored in RAM so you can upgrade communications software without replacing ROM chips. The battery maintains the contents of RAM over power outages. Soft Switches are used to tailor the Ethernet Controller to your application. The MS-DOS or Windows Configuration Software package is used to configure the Ethernet Controller in the IC697 PLC, and to set the soft switches for the Ethernet Controller. More detailed information about the Ethernet Controller, hardware installation, attachment to the Ethernet LAN, and Ethernet software follows this overview. For a complete description, refer to the User s Manual that applies to the software you choose to run on it. These related publications are listed on page 8. IEEE 802.3 Media The Ethernet Controller can operate on any of the following media with the appropriate user-supplied transceiver cable and transceiver. IEEE 802.3 specifies the definitive requirements of each medium. 10Base5 Coax: 10Base5 uses a 0.4 inch diameter 50-ohm coaxial cable. The maximum length of a cable segment (single span of cable) is 500 meters. The distance between any two stations must be a multiple of 2.5 meters. A maximum of 100 stations is allowed on a thickwire Ethernet segment. 10Base2 Coax: 10Base2 uses a 0.2 inch diameter 50-ohm coaxial cable. The maximum length of a thinwire cable segment is 185 meters. A maximum of 30 stations is allowed on a thinwire Ethernet segment. 10BaseT: 10BaseT uses a twisted pair cable of up to 100 meters in length between each node and a hub or repeater. Typical hubs or repeaters support 6 to 12 nodes connected in a star wiring topology. 10BaseF: 10BaseF has two variations that both use the same type of fiber optic cable: 10BaseFP can support up to 33 nodes at distances of up to 500 meters from a passive star; 10BaseFL supports up to 2000 meters between a node and a repeater (a multi-port repeater would thus constitute a star). Additionally, 10BaseFB provides a means of interconnecting (only) repeaters by up to 2000 meters of (the same) fiber optic cable. Note Various Ethernet baseband media can be interconnected by appropriate repeaters. Capabilities and limitations are defined in IEEE 802.3 Chapter 13, System Considerations for Multi-Segment Networks . 10Broad36: 10Broad36 uses 75-ohm coaxial cable and CATV-like media components (taps, amplifiers, headend translators, etc.) to support hundreds of nodes at distances of up to 2800 meters. Broadband cannot be connected to baseband via repeaters. Broadband cable plant design and installation must be in accordance with IEEE 802.7 and requires special expertise. GE Fanuc recommends you contract professional specialists for these services. Consult your GE Fanuc sales representative or field service office for help in identifying local specialists. 3 Ethernet Controller GFK-0532K Communications Modules August 1997 Series 90 -70 Programmable Controller Data Sheet Manual GFK-0600F 68-3 Module Physical Description Figure 2 shows the maintenance controls and indicators of the Ethernet Controller. TRANSCEIVER CABLE 15 PIN ETHERNET CONNECTOR MODEL 70 CMM 741 MODULE OK ONLINE STATUS OK BATTERY CONNECTIONS UNPLUGGING OLD ON OR BLINK= OK MODULE IC697CCM741 LABEL 44A726758 117R01 RESTART PUSHBUTTON Y R E BATT OPEN REPLACEMENT BATTERY CONNECTOR CURRENTLY INSTALLED BATTERY CONNECTOR 9 PIN SERIAL PORT LEDS GROUND WIRE DEFAULT STATION ADDRESS LABEL WARNING SERIAL RS 232 DTE 2 TX (OUT) 3 RX (IN) PUSH SLIDE FROM FRONT TO LOCK: FROM BACK TO RELEASE WHEN RUNNING DIAGNOSTICS) PUSH TO RESTART LAN INTERFACE. PUSH AND HOLD TO REQUEST LAN INTERFACE DOWNLOAD. (INOP a44719 TRANSCEIVER CABLE PORT BATTERY. USE IC697ACC701 BATTERY BEFORE INSTALL NEW 7 GND Figure 2. Ethernet Controller Board User Maintenance Items The Ethernet Controller has the following useraccessible elements: Three LEDs: located at the top front of the Ethernet Controller and are visible through a window in the front door. Default Station (MAC) Address Label: affixed on the outside of the plastic housing. This MAC station address is used for network communications, unless overridden by the user. Restart Button: located immediately below the LEDs. Battery and Battery Holder: located to the right of LEDs (between Restart button and serial port). Local Serial Port: 9-pin female connector for RS-232 Interface. AUI Port: 15-pin female connector with slide-lock for transceiver cable. Located beneath the local serial port. Module Indicators The Ethernet Controller board indicators consist of three Light Emitting Diodes (LEDs): MODULE OK ONLINE STATUS OK See Figure 2 for LED location, and Table 1 for a description of these indicators. GFK-0532K Ethernet Controller 4 Communications Modules August 1997 Series 90 -70 Programmable Controller Data Sheet Manual GFK-0600F 68-4 Table 1. Ethernet Controller Indicators Indicator Status Description MODULE OK ON This LED is ON if the Ethernet Controller has passed diagnostics and its hardware is operating properly. OFF It is OFF if the module fails a diagnostic test or if a fatal failure is detected while the board is running. BLINKING This LED is blinking if the module is running diagnostics or is in Soft Switch entry state. ONLINE ON This LED is ON when the Ethernet Controller is connected to and ready to communicate on the network. OFF This LED is OFF when: - the station is not communicating in the network due to disconnection or a disruption of the cable. - the local station has malfunctioned. - the Ethernet Controller has been commanded not to enter the network or is in a state where network operation is inappropriate, such as Soft Switch Entry state or local loading. BLINKING It is BLINKING when the module is transferring data on the network or loading over the network. STATUS OK ON This LED is ON if the module is running without exception conditions. OFF This LED is OFF if the module is running and detects an event that calls for supervisory attention. In this case you should connect the GSM and follow the instructions in Chapter 8 of the User s Manual to obtain further information. BLINKING This LED is BLINKING if the module is loading or looking for a load source for the LAN Interface software. Restart Button The Restart button serves two functions: Restart, and Restart and Reload. The Restart button is inaccessible when the door to the Ethernet Controller is closed. Restart: Pressing the Restart button (for less than 5 seconds) forces a restart of the Ethernet Controller. The power-up diagnostics run and the software on the module is restarted. Restart and Reload: Pressing and holding the Restart button for 5 seconds or more requests a restart and reload of the Ethernet Controller. When the Restart button is pressed, all LEDs go out. After 5 seconds have elapsed, the STATUS OK LED will come ON to indicate that the Ethernet Controller will request a reload. Upon release of the button, the power-up diagnostics run and the Ethernet Controller requests a reload. See Configuring and Loading the Ethernet Controller for more information. Note Any data being transferred by the Ethernet Controller at the time of the Restart, or Restart and Reload, will be lost. The Restart Button is not operable during the Ethernet Controller diagnostic phase. The Ethernet Controller is in diagnostic phase when the BOARD OK LED is BLINKING and the ONLINE and STATUS OK LEDs are OFF. Battery The battery and battery holder are located to the right of the LEDs. The battery connectors are located on the board between the Restart button and the 9-pin serial port connector. When connected, the battery preserves the contents of RAM when there is no power to the board. The battery will maintain the RAM contents for a minimum of six months.

Need To Order A Specific Revision?

Give us a call at 1-800-360-6802 or 1-919-535-3180. We can help you with your Revision specific needs.


UPS Ground shipping is always FREE!


What is New Surplus?

These “New Surplus” units are a great cost saving alternative. This product is in the original manufacturer’s packaging with all sub-assemblies and documentation. Comes with a PDF Electric & Supply 3-year warranty.


UPS Ground shipping is always FREE!


What is Surplus New?

Surplus New - New unused and includes all sub-assemblies and documentation. Product may ship in manufacturer or PDF Electric & Supply packaging and includes a PDF Electric & Supply 3 Year Warranty.


UPS Ground shipping is always FREE!


What is Reconditioned?

Reconditioned products from PDF Electric & Supply are a cost-effective alternative to new and obsoleted PLC products. Every part is reconditioned down to the circuit board level. All parts are thoroughly inspected and hand-cleaned before being functionally tested in a fully configured system.


Our Reconditioned Products always come with a PDF Electric & Supply 2-Year Warranty.

UPS Ground shipping is always FREE!


110% PRICE MATCH GUARANTEE


We stand behind our prices with a 110% price match guarantee. If you buy a part from us and, within seven days of purchase, find that part advertised on an authorized distributor's website for less, simply contact us and give us a link to the lower advertised price and we'll refund you 110% of the difference between your purchase price and the advertised lower price. The part must be in-stock for immediate shipment and be in similar condition. All pricing must be displayed without signing in.

Repair Service


3-5 Days for most repairs. 24 hour repair upon request at no extra charge. If part is unrepairable, we will exchange with a working unit or return unrepaired.